Our Wire Specifications
Standard Type #135
Size Group S: Single panel partitions ranging in height from 7'0" to 12'0". Floor and/or ceiling bracing can be installed for added reinforcement where required.
- Wire mesh partitions shall be Standard Wire & Steel Works, type #135, size group S
- 10 gauge (.135 in) steel wire, woven into 1 1/2" diamond mesh, with wire securely clinched to framing
- Wire shall be woven through a horizontal 1" x 1/2" x 12 gauge channel bar at 3'6 1/8" from bottom of partition
- Vertical frames 1 1/4" x 5/8" C-type, cold rolled channel. Horizontal frames 1" x 1/2" x 12 gauge channel, mortised and tenoned at intersections
- Top capping bar 2 1/2" x 3/4"cold rolled channel with 1/4" U-bolts approximately 18" oc.
- Corner post 1 1/4" x 1 1/4" x 1/8" angle
- Slide door frames 1 1/2" x 3/4" x 12 gauge channel. Hinged foor frames 1 1/4" x 1/2" x 12 gauge channel with 1 1/4" x 1/8" cover plate on four sides
- Sliding doors to have: Two 4-wheel ballbearing trucks hung in enclosed box track, slide door strike keeper, bottom guide channel
- Hinged doors to have: 1 1/2" pair fast pin butts, continuous 1 3/8" x 7/8" x 1/8" angle strike
- 3" sweep space under all panels and doors
- Aluminum cylinder mortise type locks with cylinders individually keyed or keyed alike. All locks to have recessed knobs on the inside
- All hardware necessary for proper installation to be furnished
- Finish: Grey powder coat (or specify other color if required)
Size Group D: Partitions with upper and lower panels for heights in excess of 12'0", usually extending from floor to overhead. Tubing posts are installed for vertical reinforcement between panels.
- Wire mesh partitions shall be Standard Wire & Steel Works, type #135, size group D
- 2" x 2" x 14 gauge tubing posts between all panels
- Specs b-m for Standard Type #135 size group S also apply to size group D
Sheet Bases (Option Only): For type of partition add sheet base after size group
- 16 gauge steel sheet welded in lower 3'6 1/8" portion of panel
- Specs for Standard Type #135 size group S and D remain the same
Standard Type #192
Size Group S: Single panel partitions ranging in height from 7'0" to 10'0". Floor and/or ceiling bracing can be installed for added reinforcement where required.
- Wire mesh partitions shall be Standard Wire & Steel Works, type #192, size group S
- 6 gauge (.192 in) steel wire, woven into 2" diamond mesh, with wire securely clinched to framing
- Wire shall be woven through a horizontal 1 1/2" x 3/4" x 12 gauge channel bar at 3'5" from bottom of partition
- Vertical and horizontal frames 1 1/2" x 3/4" x 12 gauge channel, mortised and tenoned at intersections
- Top capping bar 3" - 4.1lb hot rolled channel with 1/4" U-bolts approximately 18" oc.
- Corner post 1 3/4" x 1 3/4" x 1/8" angle
- Door frames 1 1/2" x 3/4" x 12 gauge channel with 1 1/2" x 1/8" cover plate on four sides
- Sliding doors to have: Two 4-wheel ballbearing trucks hung in enclosed box track, slide door strike keeper, bottom guide channel
- Hinged doors to have: 1 1/2" pair fast pin butts, continuous 1/8" angle strike
- 3" sweep space under all panels and doors
- Aluminum cylinder mortise type locks with cylinders individually keyed or keyed alike. All locks to have recessed knobs on the inside
- All hardware necessary for proper installation to be furnished
- Finish: Grey powder coat (or specify other color if required)
Size Group D: Partitions with upper and lower panels for heights in excess of 10'0", usually extending from floor to overhead. Tubing posts are installed for vertical reinforcement between panels.
- Wire mesh partitions shall be Standard Wire & Steel Works, type #192, size group D
- 2" x 2" x 14 gauge tubing posts between all panels
- Specs b-m for Standard Type #192 size group S also apply to size group D
Sheet Bases (Option Only): For type of partition add sheet base after size group
- 16 gauge steel sheet welded in lower 3'6 1/8" portion of panel
- Specs for Standard Type #192 size group S and D remain the same